I&rsquove truly liked the glance of acrylic floating frames- they&rsquore modern-day and that brass components- swoon! But they&rsquore rather high priced. I saw one on West Elm, but it was $a hundred and eighty. Nope- that&rsquos over my budget. So I considered I could make my own. I&rsquoll be genuine, I&rsquoll struggled with this Do-it-yourself acrylic frame, but I&rsquoll notify you how to stay clear of my problems so you can conveniently make a single.
It was a enjoyment task! And by the close I was actually delighted to be done with it- lol! But we bought some cute images jointly and it&rsquos fun to have a little snapshot of this minute in time with my tiny guy. The very best part of this huge picture venture- while it was a ache to do, it was cost-free! Truly it value me $3 to get the 12 shots printed to four&Primex6&Primary. Which is pretty much absolutely nothing!
In addition to the prints, I imagined it&rsquod be enjoyment to involve paint swatches from my rainbow stairs. This was free of charge and I imagined it&rsquod assist notify the color tale even far more evidently. The shades I grabbed from Residence Depot are- 1. Beloved Pink, two. Shy Smile, 3. Coral Fountain, 4. Lamplit, 5. Corn Stalk, 6. Frittata, seven. Sparkling Brook, eight. Green Aqua, 9. Mirador, 10. Tinted Ice, 11. Early September, and 12. Blue Chalk
- 2 items of 18&Primex24&Primary plexiglass (.093 thick)
- Brass Signal Standoffs&ndash I utilized four for my frame (just one on every single corner). This features screws and anchors for hanging.
- Art. I applied twelve parts of three&Primex5&Prime prints. One huge piece of sixteen&Primex20&Prime art would be great far too
- Glue Dots for keeping the art on the plexiglass
- Drill and whole established of drill bits 
I only needed to purchase the plexiglass which was $24 and brass signal standoffs (they were $seven) for this undertaking, additionally the $three in art. So I spent a overall of $34 on this venture. Much additional very affordable than the $one hundred eighty to get it new!
I acquired my acrylic sheets at Home Depot. Suggestion- before I do any project the place I need to have to purchase supplies from a hardware store, I look the item up on the web to make confident there&rsquos inventory at my keep. Then I can also note the aisle and bay the product is on that&rsquos observed on the merchandise details website page. I get a screenshot of that info or compose it down in the notes part of my mobile phone. This designed it straightforward to uncover the plexiglass.
Suitable now, acrylic is in a bit of higher need since they&rsquore getting applied for sneeze guards. It was hard to come across these, so just a heads up that you might have to verify Lowes and House Depot and probably push to come across some in inventory.
For the indication standoffs, the components for the corners, I acquired that on line at Amazon. I acquired the brass version. They are also out there in matte black, polished chrome, and brushed silver. Buy the color that&rsquoll will do the job finest for your design so you don&rsquot have to trouble with spray painting it.
Begin by receiving the art prepared to body. For me, that looked like trimming the title and emblem off the paint swatches. Continued trimmed my four&Primex6&Key prints down to 4&Primex5&Key. That way they properly in good shape on my 18&Primex24&Prime plexiglass body.
Following, it&rsquos time to drill holes into the plexiglass so I could hold it with the signal standoff components. I was nervous about this element. 
To drill the holes, I to start with place painter&rsquos tape on the entrance and back again on both equally items of plexiglass in the corners. Take note, don&rsquot remove the protecting sheet on the acrylic- leave it on so it doesn&rsquot get scratched up. Both equally the protective sheet and painters tape will assistance prevent cracks..
Next, mark on the major of the tape where by the holes must go. Mine ended up one 1/4&Key from each and every aspect. I place a scrap piece of wooden underneath the acrylic to protect my desk.
The largest point you want to avoid with this phase is cracking the acrylic. So what you do is start with a small drill little bit and then function your way up to a bigger just one. I started with a one/8&Prime facet than three/16&Prime, then one/four&Prime then 5/sixteen&Primary, then 3/eight&Prime to eventually have a huge ample hole that the hardware suit properly. Tip- if you get a thicker piece of acrylic, you&rsquore less possible to crack the glass.
A further idea- if you have additional than just one drill, use it! That saves you time with switching out drill bits. It took me about three minutes to drill out a person hole. So about thirty minutes between two sheets. For the 2nd sheet, lay the completed sheet on best and then mark the holes by putting a sharpie via the primary hole so they both match up.
Unfortunately, on the very past gap that I was drilling, I unintentionally cracked the glass with the biggest drill little bit. It was like it caught on some thing. I was devastated! And so unhappy. In hind sight, I wish I had tried using the strategy where you heat up a landscaping spike on the stove and melt the plexiglass. This site has fantastic instructions for making the gap.
It&rsquoll cost $five more to do, but it saves a ton of time and stress. So it&rsquos thoroughly worth it!
Because I couldn&rsquot locate any excess sheets of plexiglass inside of thirty minutes of my house, I made the decision to use what I experienced and put it on the back. When they are in inventory, I can get a new sheet and substitute the damaged a single out.
And now, make absolutely sure the holes on the two parts of plexiglass match up and the hardware can go as a result of all 4 holes. If not, drill out wherever is needed. 
The moment the components goes on properly, take away all painter&rsquos tape and the protective film off the front and again of the acrylic.
At this point, the plexiglass will be really messy. To clean up it, you&rsquoll want to be super thorough. If you wipe the tiny items of glass that was drilled off, it could scratch the surface. Rather, use a blow dryer on the amazing placing to blow off any modest parts.
Next, use a microfiber fabric and a remedy of h2o and dish soap and wipe down the two surfaces of the acrylic. Then, use a clean towel to wipe off the cleaning soap till the plexiglass is clean up.
I identified it most effective to lay a thoroughly clean blanket on my mattress and then work on the plexiglass though it was laying down.
Last but not least, it&rsquos time to put the art involving the two items of plexiglass. At initially, I considered I would be able to just set the components on and the artwork would be held up. Nope! I couldn&rsquot get it limited sufficient to maintain it up! Dang! So alternatively, I had to use glue dots on the back of each and every print and paint swatch to keep them in place. 
Now it&rsquos time to dangle! So I took my body to my guest bed room exactly where it&rsquoll go more than the dresser. Pardon the mess in in this article, we&rsquore renovating the bathroom right subsequent to this home and so there&rsquos containers of tiles and a toilet and self-importance cluttering up the home. You&rsquove acquired to enjoy a huge undertaking!
I held up my body. I had it assembled with the components installed in the corners. When I knew where I required it, I place minimal dabs of toothpaste on the back again of the components, ideal over where by the screw holes exactly where. Then I touched the body to the wall (whilst a stage was balanced on best) and the toothpaste acquired transferred to the wall!
That&rsquos where I screwed in the back again of the components to the wall. Another possibility is to hold up the plexiglass without having the hardware in it and just mark where by the holes are. Because you have to make four holes in the wall, it&rsquos critical to be precise with this stage. The pleasant factor about the components I acquired is that it will come with screws and anchors so that will make hanging simpler. 
The moment the back again of the components is on, put the two sheets of plexiglass on the components and screw the leading piece on. At this stage, you&rsquore finished!
And right here it is all hung up! You can&rsquot genuinely see the crack- it&rsquos on the bottom right hand side. Primarily, it&rsquos a sweet and playful piece of art!
I enjoy the contemporary body and how gentle and ethereal it is in this area. Even though it&rsquos an very affordable job, it&rsquos at least a medium to superior amount of Diy. I bought pretty pissed off along the way. But I imagine with the strategies I added in this put up, you can stay away from my mistakes. 
I required to demonstrate you this watch, it&rsquos ideal about the corner from my rainbow mural. They glance so fun up coming to each and every other! I&rsquom really loving the vibrant art below. I rarely dangle private photographs, but I like how these are both sweet, and operate with the color story in right here. This piece is truly building me pleased!
As lots of of you know, in the wintertime we hire our property as an Air BNB. Considering that it&rsquoll be a rental, I needed to acquire down the particular images and switch them out for colourful floral artwork. I could possibly really like it more now!
I established these graphics to match my rainbow shades. I believed it&rsquod be pleasurable to give them as a free download!
To download the no cost printable, just set your name and email in the sort underneath. You&rsquoll get an e mail proper absent with how to download. Plus you&rsquoll be subscribed to my weekly publication! If you&rsquore presently subscribed, go listed here to down load.
What do you consider? Do you like it? Would you make just one? Enable me know if you have any queries in the remarks!
This publish incorporates some affiliate back links for your comfort. Click below to read through my total disclosure policy.
 
If you love it, pin it!